Xd Series Rotary Vane Vacuum Pump

Model NO.: XD
Trademark: SUOTO
Origin: Shanghai, China
HS Code: 8414100090
Model NO.: XD
Trademark: SUOTO
Origin: Shanghai, China
HS Code: 8414100090
XD series rotary vane vacuum pump is a single-stage multi-vane type vacuum pump seal, is a basic vacuum equipment. It has an eccentric pump with the pump installed and a fixed straight linetangent to the inside surface of the rotor, the rotor slot may have three radial sliding vane. Centrifugal force when the rotor vane and the wall is always contact with the pump, rotary vane pump chamber volume can be divided into three working chamber cycle. Working chamber volume of the cycle do so to complete the suction pump, exhaust. Each switch, pump the gas removing part of the container until it reaches the limit of vacuum pressure.

Characteristics:
1. Direct transmission, compact, light weight;
2. Air cooling, no water, easy to operate, use, low maintenance costs;
3. Multi-vane and the bottom is equipped with rubber pads, smooth, little vibration;
4. Turn a pump oil separator can effectively remove small oil mist exhaust;
5. Pump design with automatic oil circulation system, often without refueling;
6. Pump that has the automatic suction valve when the pump stops working, automaticallypump suction valve and pumping system to be isolated to prevent the pump is pumping the oil back into the system;
7. Pumping efficiency, the inlet pressure close to the limit pressure is still a high pumping speed.

Performance Parameters
  Model Capacity
(m 3 /h)		 Limited Pre. ≤ (Pa)
XD-xx(Z) XD-xxQ
                 		 Power
(kw)		 Speed
(rpm)		 Oil Consumption
                          (L)		 Inlet Weight
(kg)		 dB(A)≤
XD-10 10 200 3000 0.37 1400 0.5 G 1/2″ 16 69
XD-20 20 200 3000 0.9(220)0.75 2800 0.5 G 1/2″ 18 71
XD-25 25 200 3000 0.9 2800 0.5 G 3/4″ 18 73
XD-40 40 200 2000 1.5 1440 1.5 G 1 1/4″ 58 75
XD-63 63 200 2000 1.5 1440 2 G 1 1/4″ 62 76
XD-100 100 200 2000 3 1440 2.5 G 1 1/4″ 89 77
XD-160 160 200 2000 4 1440 9 G 2″ 145 79
XD-250 250 200 2000 7.5 1440 9 G 2″ 200 80
XD series rotary vane vacuum pump is a single-stage multi-vane type vacuum pump seal, is a basic vacuum equipment. It has an eccentric pump with the pump installed and a fixed straight linetangent to the inside surface of the rotor, the rotor slot may have three radial sliding vane. Centrifugal force when the rotor vane and the wall is always contact with the pump, rotary vane pump chamber volume can be divided into three working chamber cycle. Working chamber volume of the cycle do so to complete the suction pump, exhaust. Each switch, pump the gas removing part of the container until it reaches the limit of vacuum pressure.

Characteristics:
1. Direct transmission, compact, light weight;
2. Air cooling, no water, easy to operate, use, low maintenance costs;
3. Multi-vane and the bottom is equipped with rubber pads, smooth, little vibration;
4. Turn a pump oil separator can effectively remove small oil mist exhaust;
5. Pump design with automatic oil circulation system, often without refueling;
6. Pump that has the automatic suction valve when the pump stops working, automaticallypump suction valve and pumping system to be isolated to prevent the pump is pumping the oil back into the system;
7. Pumping efficiency, the inlet pressure close to the limit pressure is still a high pumping speed.

Performance Parameters
  Model Capacity
(m 3 /h)		 Limited Pre. ≤ (Pa)
XD-xx(Z) XD-xxQ
                 		 Power
(kw)		 Speed
(rpm)		 Oil Consumption
                          (L)		 Inlet Weight
(kg)		 dB(A)≤
XD-10 10 200 3000 0.37 1400 0.5 G 1/2″ 16 69
XD-20 20 200 3000 0.9(220)0.75 2800 0.5 G 1/2″ 18 71
XD-25 25 200 3000 0.9 2800 0.5 G 3/4″ 18 73
XD-40 40 200 2000 1.5 1440 1.5 G 1 1/4″ 58 75
XD-63 63 200 2000 1.5 1440 2 G 1 1/4″ 62 76
XD-100 100 200 2000 3 1440 2.5 G 1 1/4″ 89 77
XD-160 160 200 2000 4 1440 9 G 2″ 145 79
XD-250 250 200 2000 7.5 1440 9 G 2″ 200 80

Plastic Injection Accessories

According to the characteristics of molding, injection mold and thermoplastic plastic mold are divided into two types. According to the molding process, it can be divided into transfer mold, blow mold, casting mold, hot molding mold, hot pressing mold (compression mold), injection mold, etc. Among them, the hot pressing mold can be divided into three types, i.e., overflow, semi-overflow and non-overflow, and the injection mold can be divided into two types, i.e., cold runner mold and hot runner mold. It can be divided into two types: mobile type and fixed type.

Plastic Injection Accessories,Injection Molded Leakproof Accessories,Plastic Handles For Boxes,Black Plastic Handles,Plastic Injection Molding Service

Timeplex Industrial Limited , https://www.hktimeplex.com

Posted on