Aluminum Material and 2-Way Speakers Design Car Speakers Horn

Technical parameter:
Features:
1.The real test in our laboraroy that show to us the horn can get 110db at least.
2.Super long surround sound,it make the sound powerful and comfortable so that decrease the trafficaccident.
3.We used the imported high quality manganese steel to make the soundboad so that can make the fullest possible "BABA~~" sound.
4.We use the most advanced Teflon coat technology.I can be dust-proof and water-proof effectively(We must inform you that there are not have any horn factory can make a universal horn that all waterproof).It prolong the lifetime of the horn effectively.
5.We used the 100%ABS material to make the horn bulb.It has very good Heat resistance,impact resistance,anti-corrosion so that can prevent the dinas and the heat of the engine damage for the horn.Anyway,it also has high hardness characteristic.It can drop from 1 meter that is not easy to break.

What should I note when I am Installing and using?
a. Snail down or 45 degree Angle installation, Prevent water  into coiled directly
b. If you are not special peason , dont change the angle degree of Steel Support,or it will change the Original air gap
c. mounting torque of Steel support is between 6Nm to 11Nm.
d. The horn support should be mounted to Solid surface to avoid resonance.
e. In order to avoid contact with other parts of the car,The horn should be connected with horn support and installed to wide and Ventilated place.
f. Nonpolarity requirements for this product, the connected place of the wire should solid enough, Double horn should installed on solid part of car body in parallel way.
g. Keep away from car motor and much Radiation place. Not be too low mounting.
h. Don't keep the horn on for 60 seconds, or it will lead to the coil burned down.
i. Using copper wire, more than 1.5mm for wire Diameter, the wire length should less than 4m.
j. Standard mounting Voltage, input working current more than 30A,12V horn voltage: 9-14.5V  


Our company is a professional manufacturer and exporter that is concerned with the design , development and production of auto parts , we are
fully committed to producing technologically advanced auto parts.


Contact us:
Guangzhou Jindong Electronic Technology Co.,LTD 
Add: No.1,Gudong Industrial Zone,Gulong Road,ShawanTownship,Panyu District,Guangzhou

Benki Huang

Tel:+86-020-34738085                                  
Mob:+86-13922729780
Fax:+86-020-84737552 
 
 
                                         
 
 




Technical parameter:
Features:
1.The real test in our laboraroy that show to us the horn can get 110db at least.
2.Super long surround sound,it make the sound powerful and comfortable so that decrease the trafficaccident.
3.We used the imported high quality manganese steel to make the soundboad so that can make the fullest possible "BABA~~" sound.
4.We use the most advanced Teflon coat technology.I can be dust-proof and water-proof effectively(We must inform you that there are not have any horn factory can make a universal horn that all waterproof).It prolong the lifetime of the horn effectively.
5.We used the 100%ABS material to make the horn bulb.It has very good Heat resistance,impact resistance,anti-corrosion so that can prevent the dinas and the heat of the engine damage for the horn.Anyway,it also has high hardness characteristic.It can drop from 1 meter that is not easy to break.

What should I note when I am Installing and using?
a. Snail down or 45 degree Angle installation, Prevent water  into coiled directly
b. If you are not special peason , dont change the angle degree of Steel Support,or it will change the Original air gap
c. mounting torque of Steel support is between 6Nm to 11Nm.
d. The horn support should be mounted to Solid surface to avoid resonance.
e. In order to avoid contact with other parts of the car,The horn should be connected with horn support and installed to wide and Ventilated place.
f. Nonpolarity requirements for this product, the connected place of the wire should solid enough, Double horn should installed on solid part of car body in parallel way.
g. Keep away from car motor and much Radiation place. Not be too low mounting.
h. Don't keep the horn on for 60 seconds, or it will lead to the coil burned down.
i. Using copper wire, more than 1.5mm for wire Diameter, the wire length should less than 4m.
j. Standard mounting Voltage, input working current more than 30A,12V horn voltage: 9-14.5V  


Our company is a professional manufacturer and exporter that is concerned with the design , development and production of auto parts , we are
fully committed to producing technologically advanced auto parts.


Contact us:
Guangzhou Jindong Electronic Technology Co.,LTD 
Add: No.1,Gudong Industrial Zone,Gulong Road,ShawanTownship,Panyu District,Guangzhou

Benki Huang

Tel:+86-020-34738085                                  
Mob:+86-13922729780
Fax:+86-020-84737552 
 
 
                                         
 
 

CNC Busbar sawing machine is developed by our company. Specially for quick busbar cutting.

â‘ Busbar cut by saw blade can be beautiful section surface and smaller waste.

â‘¡Auto clamp with stroke 2000mm.

â‘¢Driven by spindle motor. Use high speed carbide disc blade.

â‘£High precision ball screw, linear guide rail, servo motor for position of

clamp and saw blade feeding. Assure high accuracy and work efficiency!

⑤Imported and branded components assure machine life and reliable quality.

â‘¥As per different width of busbar. Machine can be customerized!

Busbar Cutting Machine

Copper Cutting Machine,Busbar Cutting Machine,Hydraulic Busbar Cutter,Die Cutting Machine

JINAN EURO-ASIA INT'L CO., LTD , https://www.eaelectricmachine.com